Kitchenaid Electric Slide-In Range Hinge Receiver Replacement #W10647259

Print ContentSave Content

Skill Level

Total Parts Cost

$5.50

Estimated Savings

$112.50

06:59

Description

This video provides step-by-step instructions for replacing the hinge receiver on a Kitchenaid electric slide-in range (model #KSEB900ESS2). The most common reason for replacing the receiver is if the door will not open or close properly.

All of the information in this hinge receiver replacement video is applicable to the following brands: Maytag, Amana, Magic Chef, Whirlpool, Tappan, Estate, Kitchenaide

Step By Step Instructions

Print Instructions

KitchenAid Electric Slide-In Range - KSEB900ESS2

Electric Range Hinge Receiver Replacement

Tools needed: Phillips head screwdriver, flat-head screwdriver

Shock

Be sure to unplug the power cord or shut off the power supply.

Open the oven door and use a Phillips head screwdriver to unthread the screws securing the control panel?s lower cover.

Sharp

Remove the cover.

Next, unthread the two screws securing the control panel to the frame.

Detach the control panel and support it to avoid straining the wires.

Now unthread the front bracket screws securing the main top.

Unthread the two screws underneath the rear corners of the top.

Heavy

Pull the main top back and up to remove then set it aside.

Rotate both oven door hinge locks back.

Heavy

Partially close the door, then lift and pull the door toward you to remove.

With the handle side down, set the door on a blanket.

Unthread the two screws securing the element support panel to the left-or-right side panel, depending on which hinge receiver you?re replacing.

Next, unthread the three screws to release the stop bracket.

Now unthread the five remaining screws securing the side panel.

Sharp

Use a flat-head screwdriver to depress the retaining tab at the rear and you can fully detach the panel.

Use the Phillips-head screwdriver or a number two square drive bit to unthread the mounting screws to release the old hinge receiver.

Install the new hinge receiver by aligning it on the frame, then thread and tighten the mounting screws.

Reinstall the side panel by aligning the frame tabs with the slots on the front of the panel, then snap the panel into position.

Secure it with the screws.

Realign the stop bracket and thread the screws to hold it in place.

Replace the screws securing the element support panel to the side panel.

Reinstall the oven door by inserting the door hinges into the hinge slots at a forty-five degree angle.

Lower the door to its fully open position, then rotate the hinge locks forward.

Reposition the main top by sliding the rear edge under the lip of the element support panel, then lower the front edge.

Replace all of the screws to secure.

Realign the control panel on the front brackets.

Secure it with the screws.

Replace the lower cover, then thread the screws to secure.

Plug the power cord back in or restore the power supply and the electric range should be ready for use.

Description

Step-By-Step Instructions

KitchenAid Electric Slide-In Range - KSEB900ESS2

Electric Range Hinge Receiver Replacement

Tools needed: Phillips head screwdriver, flat-head screwdriver

Shock

Be sure to unplug the power cord or shut off the power supply.

Open the oven door and use a Phillips head screwdriver to unthread the screws securing the control panel?s lower cover.

Sharp

Remove the cover.

Next, unthread the two screws securing the control panel to the frame.

Detach the control panel and support it to avoid straining the wires.

Now unthread the front bracket screws securing the main top.

Unthread the two screws underneath the rear corners of the top.

Heavy

Pull the main top back and up to remove then set it aside.

Rotate both oven door hinge locks back.

Heavy

Partially close the door, then lift and pull the door toward you to remove.

With the handle side down, set the door on a blanket.

Unthread the two screws securing the element support panel to the left-or-right side panel, depending on which hinge receiver you?re replacing.

Next, unthread the three screws to release the stop bracket.

Now unthread the five remaining screws securing the side panel.

Sharp

Use a flat-head screwdriver to depress the retaining tab at the rear and you can fully detach the panel.

Use the Phillips-head screwdriver or a number two square drive bit to unthread the mounting screws to release the old hinge receiver.

Install the new hinge receiver by aligning it on the frame, then thread and tighten the mounting screws.

Reinstall the side panel by aligning the frame tabs with the slots on the front of the panel, then snap the panel into position.

Secure it with the screws.

Realign the stop bracket and thread the screws to hold it in place.

Replace the screws securing the element support panel to the side panel.

Reinstall the oven door by inserting the door hinges into the hinge slots at a forty-five degree angle.

Lower the door to its fully open position, then rotate the hinge locks forward.

Reposition the main top by sliding the rear edge under the lip of the element support panel, then lower the front edge.

Replace all of the screws to secure.

Realign the control panel on the front brackets.

Secure it with the screws.

Replace the lower cover, then thread the screws to secure.

Plug the power cord back in or restore the power supply and the electric range should be ready for use.

Applicable Product Model

Brand

KitchenAid

Product Type

Range/Stove/Oven

Model

KSEB900ESS2

Subtype

Electric

Product Diagram & Manuals

Parts Needed

Hinge Bracket

$5.50

Recommended Tools and Accessories

Cooktop Cleaner

$14.19

Total$0.00

Kitchenaid Electric Slide-In Range Hinge Receiver Replacement #W10647259

Step By Step Instructions

Applicable Product Model

Related Articles & Videos