Kitchenaid Electric Slide-In Range Cooling Fan Replacement #W11107275

Print ContentSave Content

Skill Level

Total Parts Cost

$105.29

Estimated Savings

$112.50

05:55

Description

This video provides step-by-step instructions for replacing the cooling fan on a Kitchenaid electric slide-in range (model #KSEB900ESS2). The most common reason for replacing the fan is if the oven is overheating.

All of the information in this fan replacement video is applicable to the following brands: Maytag, Amana, Magic Chef, Whirlpool, Tappan, Estate, Kitchenaide

Step By Step Instructions

Print Instructions

KitchenAid Electric Slide-In Range - KSEB900ESS2

Electric Range Cooling Fan Assembly Replacement

Tools needed: Phillips-head screwdriver

Shock

Be sure to unplug the power cord or shut off the power supply.

Open the oven door and use a Phillips-head screwdriver to unthread the screws securing the control panel?s lower cover.

Sharp

Remove the cover.

Next, unthread the two screws securing the control panel to the frame.

Detach the control panel and support it to avoid straining the wires.

Now unthread the front bracket screws securing the main top.

Unthread the two screws underneath the rear corners of the top.

Heavy

Pull the main top back and up to remove then set it aside.

Now unthread the four screws securing the element support panel to the side panels.

Sharp

You can now detach the panel from the front brackets for more clearance to the cooling fan assembly.

Unthread the mounting screw securing the fan assembly to the left front bracket.

Push the fan assembly back to detach and you can slide it forward.

Disconnect the wire connecters to fully remove the old assembly.

Prepare the new cooling fan assembly for installation by transferring the seal from the old assembly to the new one?or install a new seal.

Now connect the wire connecters.

Align the fan assembly tabs with the panel slots and push the assembly forward.

Thread the mounting screw to secure the assembly to the bracket.

Realign the element support panel by snapping the tabs into the front brackets.

Replace the screws.

Reposition the main top by sliding the rear edge under the lip of the element support panel, then lower the front edge.

Replace all of the screws to secure.

Realign the control panel on the front brackets.

Secure it with the screws.

Replace the lower cover, then thread the screws to secure.

Plug the power cord back in or restore the power supply and the electric range should be ready for use.

Description

Step-By-Step Instructions

KitchenAid Electric Slide-In Range - KSEB900ESS2

Electric Range Cooling Fan Assembly Replacement

Tools needed: Phillips-head screwdriver

Shock

Be sure to unplug the power cord or shut off the power supply.

Open the oven door and use a Phillips-head screwdriver to unthread the screws securing the control panel?s lower cover.

Sharp

Remove the cover.

Next, unthread the two screws securing the control panel to the frame.

Detach the control panel and support it to avoid straining the wires.

Now unthread the front bracket screws securing the main top.

Unthread the two screws underneath the rear corners of the top.

Heavy

Pull the main top back and up to remove then set it aside.

Now unthread the four screws securing the element support panel to the side panels.

Sharp

You can now detach the panel from the front brackets for more clearance to the cooling fan assembly.

Unthread the mounting screw securing the fan assembly to the left front bracket.

Push the fan assembly back to detach and you can slide it forward.

Disconnect the wire connecters to fully remove the old assembly.

Prepare the new cooling fan assembly for installation by transferring the seal from the old assembly to the new one?or install a new seal.

Now connect the wire connecters.

Align the fan assembly tabs with the panel slots and push the assembly forward.

Thread the mounting screw to secure the assembly to the bracket.

Realign the element support panel by snapping the tabs into the front brackets.

Replace the screws.

Reposition the main top by sliding the rear edge under the lip of the element support panel, then lower the front edge.

Replace all of the screws to secure.

Realign the control panel on the front brackets.

Secure it with the screws.

Replace the lower cover, then thread the screws to secure.

Plug the power cord back in or restore the power supply and the electric range should be ready for use.

Applicable Product Model

Brand

KitchenAid

Product Type

Range/Stove/Oven

Model

KSEB900ESS2

Subtype

Electric

Product Diagram & Manuals

Parts Needed

Cooling Fan

$105.29

Recommended Tools and Accessories

Cooktop Cleaner

$14.19

Total$0.00

Kitchenaid Electric Slide-In Range Cooling Fan Replacement #W11107275

Step By Step Instructions

Applicable Product Model

Related Articles & Videos