Kitchenaid Electric Slide-In Range Control Board Replacement #W11128223

Print ContentSave Content

Skill Level

Total Parts Cost

$379.35

Estimated Savings

$112.50

08:20

Description

This video provides step-by-step instructions for replacing the control board on a Kitchenaid electric slide-in range (model #KSEB900ESS2). The most common reason for replacing the board is if the range does not work at all.

All of the information in this board replacement video is applicable to the following brands: Maytag, Amana, Magic Chef, Whirlpool, Tappan, Estate, Kitchenaide

Step By Step Instructions

Print Instructions

KitchenAid Electric Slide-In Range - KSEB900ESS2

Electric Range Control Board Replacement

Tools needed: Phillips-head screwdriver

Shock

Be sure to unplug the power cord or shut off the power supply.

Open the oven door and use a Phillips-head screwdriver to unthread the screws securing the control panel?s lower cover.

Sharp

Remove the cover.

Next, unthread the two screws securing the control panel to the frame.

Detach the control panel

Note the orientation of the wire connecters, then disconnect them.

Set the control panel aside.

Now unthread the front bracket screws securing the main top.

Unthread the two screws underneath the rear corners of the top.

Heavy

Pull the main top back and up to remove then set it aside.

Next, unthread the screws to detach the center front bracket.

Now unthread the four screws securing the element support panel to the side panels.

Sharp

You can now detach the panel from the front brackets for more clearance to the control board.

Remove the screws securing the control board mounting plate.

Pull the assembly forward.

Note the orientation of the wire connecters connected to the board, then disconnect them.

Prepare the new control board for installation by transferring the mounting plate from the old board to the new one.

Transfer the ribbon connecter as well.

Connect the wire connecters to the appropriate terminals.

Position the control board assembly so the tab on the bottom of the mounting plate is inserted into the slot in the panel.

Thread and tighten the mounting screws.

Realign the element support panel by snapping the tabs into the front brackets.

Replace the screws.

Reposition the center front bracket and secure it with the screws.

Reposition the main top by sliding the rear edge under the lip of the element support panel, then lower the front edge.

Replace all of the screws to secure.

Connect all of the wire connecters to the appropriate terminals on the control panel.

Realign the control panel on the front brackets.

Secure it with the screws.

Replace the lower cover, then thread the screws to secure.

Plug the power cord back in or restore the power supply and the electric range should be ready for use.

Description

Step-By-Step Instructions

KitchenAid Electric Slide-In Range - KSEB900ESS2

Electric Range Control Board Replacement

Tools needed: Phillips-head screwdriver

Shock

Be sure to unplug the power cord or shut off the power supply.

Open the oven door and use a Phillips-head screwdriver to unthread the screws securing the control panel?s lower cover.

Sharp

Remove the cover.

Next, unthread the two screws securing the control panel to the frame.

Detach the control panel

Note the orientation of the wire connecters, then disconnect them.

Set the control panel aside.

Now unthread the front bracket screws securing the main top.

Unthread the two screws underneath the rear corners of the top.

Heavy

Pull the main top back and up to remove then set it aside.

Next, unthread the screws to detach the center front bracket.

Now unthread the four screws securing the element support panel to the side panels.

Sharp

You can now detach the panel from the front brackets for more clearance to the control board.

Remove the screws securing the control board mounting plate.

Pull the assembly forward.

Note the orientation of the wire connecters connected to the board, then disconnect them.

Prepare the new control board for installation by transferring the mounting plate from the old board to the new one.

Transfer the ribbon connecter as well.

Connect the wire connecters to the appropriate terminals.

Position the control board assembly so the tab on the bottom of the mounting plate is inserted into the slot in the panel.

Thread and tighten the mounting screws.

Realign the element support panel by snapping the tabs into the front brackets.

Replace the screws.

Reposition the center front bracket and secure it with the screws.

Reposition the main top by sliding the rear edge under the lip of the element support panel, then lower the front edge.

Replace all of the screws to secure.

Connect all of the wire connecters to the appropriate terminals on the control panel.

Realign the control panel on the front brackets.

Secure it with the screws.

Replace the lower cover, then thread the screws to secure.

Plug the power cord back in or restore the power supply and the electric range should be ready for use.

Applicable Product Model

Brand

KitchenAid

Product Type

Range/Stove/Oven

Model

KSEB900ESS2

Subtype

Electric

Product Diagram & Manuals

Parts Needed

Display Board

$379.35

Recommended Tools and Accessories

Cooktop Cleaner

$14.19

Total$0.00

Kitchenaid Electric Slide-In Range Control Board Replacement #W11128223

Step By Step Instructions

Applicable Product Model

Related Articles & Videos