In-stock parts ship the same day
Price Match Guarantee
In-stock parts ship the same dayGET PRO PRICING
Video & Articles: Appliance & Equipment RepairKitchenaid Electric Slide-In Range Oven Bake Element Replacement #W10779716 
Kitchenaid Electric Slide-In Range Oven Bake Element Replacement #W10779716
Skill Level
Total Parts Cost
$66.06Estimated Savings
$112.5004:14
- Description
This video provides step-by-step instructions for replacing the oven bake element on a Kitchenaid electric slide-in range (model #KSEB900ESS2). The most common reason for replacing the element is if the oven is not heating properly.
All of the information in this element replacement video is applicable to the following brands: Maytag, Amana, Magic Chef, Whirlpool, Tappan, Estate, Kitchenaide
All of the information in this element replacement video is applicable to the following brands: Maytag, Amana, Magic Chef, Whirlpool, Tappan, Estate, Kitchenaide
Step By Step Instructions
1
KitchenAid Electric Slide-In Range - KSEB900ESS2
2
Electric Range Oven Bake Element Replacement
3
Tools needed: Phillips-head screwdriver
4
Shock
5
Be sure to unplug the power cord or shut off the power supply.
6
Pull the range away from the wall so you can access the rear of the appliance.
7
Using a Phillips-head screwdriver, unthread the two screws securing the lower rear access panel.
8
Sharp
9
Lift the panel up and out to remove.
10
Disconnect the wires from the oven bake element terminals.
11
Now fully open the oven door and rotate both door hinge locks back.
12
Heavy
13
Partially close the door, then lift and pull the door toward you to remove.
14
With the handle side down, set the door on a blanket.
15
Slide out the oven racks.
16
Next, unthread the two screws securing the oven?s bottom panel.
17
Lift the panel up from the rear and pull forward to detach.
18
Unthread the screws securing the bake element to the front and rear of the oven.
19
You can now remove the old element.
20
Install the new bake element by inserting the terminals through the holes in the rear panel.
21
Fully position the element and replace the two screws to secure it.
22
Reinstall the bottom panel by aligning the front edge first.
23
Thread the screws to secure.
24
Slide the oven racks into place.
25
Reinstall the oven door by inserting the door hinges into the hinge slots at a forty-five degree angle.
26
Lower the door to its fully open position, then rotate the hinge locks forward.
27
Returning to the rear of the appliance, connect the wires to the bake element terminals.
28
Reinstall the lower access panel by inserting the tabs in the slots first.
29
Lower the panel and secure it with the screws.
30
Plug the power cord back in or restore the power supply and the electric range should be ready for use.
Description
This video provides step-by-step instructions for replacing the oven bake element on a Kitchenaid electric slide-in range (model #KSEB900ESS2). The most common reason for replacing the element is if the oven is not heating properly.
All of the information in this element replacement video is applicable to the following brands: Maytag, Amana, Magic Chef, Whirlpool, Tappan, Estate, Kitchenaide
All of the information in this element replacement video is applicable to the following brands: Maytag, Amana, Magic Chef, Whirlpool, Tappan, Estate, Kitchenaide
Step-By-Step Instructions
1
KitchenAid Electric Slide-In Range - KSEB900ESS2
2
Electric Range Oven Bake Element Replacement
3
Tools needed: Phillips-head screwdriver
4
Shock
5
Be sure to unplug the power cord or shut off the power supply.
6
Pull the range away from the wall so you can access the rear of the appliance.
7
Using a Phillips-head screwdriver, unthread the two screws securing the lower rear access panel.
8
Sharp
9
Lift the panel up and out to remove.
10
Disconnect the wires from the oven bake element terminals.
11
Now fully open the oven door and rotate both door hinge locks back.
12
Heavy
13
Partially close the door, then lift and pull the door toward you to remove.
14
With the handle side down, set the door on a blanket.
15
Slide out the oven racks.
16
Next, unthread the two screws securing the oven?s bottom panel.
17
Lift the panel up from the rear and pull forward to detach.
18
Unthread the screws securing the bake element to the front and rear of the oven.
19
You can now remove the old element.
20
Install the new bake element by inserting the terminals through the holes in the rear panel.
21
Fully position the element and replace the two screws to secure it.
22
Reinstall the bottom panel by aligning the front edge first.
23
Thread the screws to secure.
24
Slide the oven racks into place.
25
Reinstall the oven door by inserting the door hinges into the hinge slots at a forty-five degree angle.
26
Lower the door to its fully open position, then rotate the hinge locks forward.
27
Returning to the rear of the appliance, connect the wires to the bake element terminals.
28
Reinstall the lower access panel by inserting the tabs in the slots first.
29
Lower the panel and secure it with the screws.
30
Plug the power cord back in or restore the power supply and the electric range should be ready for use.
Applicable Product Model
Related Articles & Videos
02:11
Part Replacement
Kitchenaid Electric Slide-In Range Left Warming Drawer Rail Replacement #W11131365
08:20
Part Replacement
Kitchenaid Electric Slide-In Range Control Board Replacement #W11128223
05:55
Part Replacement
Kitchenaid Electric Slide-In Range Cooling Fan Replacement #W11107275
05:26
Part Replacement
Kitchenaid Electric Slide-In Range Left Front Radiant Surface Element Replacement #WPW10187839