Kitchenaid Electric Slide-In Range Right Rear Surface Element Switch Replacement #W10911303

Print ContentSave Content

Skill Level

Total Parts Cost

$93.57

Estimated Savings

$112.50

03:53

Description

This video provides step-by-step instructions for replacing the right rear surface element switch on a Kitchenaid electric slide-in range (model #KSEB900ESS2). The most common reason for replacing the switch is if the element is not heating.

All of the information in this switch replacement video is applicable to the following brands: Maytag, Amana, Magic Chef, Whirlpool, Tappan, Estate, Kitchenaide

Step By Step Instructions

Print Instructions

KitchenAid Electric Slide-In Range - KSEB900ESS2

Electric Range Right Rear Surface Element Switch Replacement

Tools needed: Phillips-head screwdriver, flat-head screwdriver

Shock

Be sure to unplug the power cord or shut off the power supply.

Open the oven door and use a Phillips-head screwdriver to unthread the screws securing the control panel?s lower cover.

Sharp

Remove the cover.

Next, unthread the two screws securing the control panel to the frame.

Place a towel on the cooktop surface then detach the control panel and rest it on the towel.

Pull off the right rear surface element switch control knob.

Unthread the two screws securing the control knob bezel and the switch itself.

If applicable, remove the gasket.

You can use a flat-head screwdriver to help disconnect the two wire connecters to fully remove the old switch.

Install the new surface element switch by first connecting the wire connecters.

Slide the gasket over the switch stem, then position the switch in the control panel

Realign the bezel with the red marking on top, then thread and tighten the two screws to secure.

Slide the knob onto the new switch stem.

Realign the control panel on the front brackets.

Secure it with the screws.

Replace the lower cover, then thread the screws to secure.

Plug the power cord back in or restore the power supply and the electric range should be ready for use.

Description

Step-By-Step Instructions

KitchenAid Electric Slide-In Range - KSEB900ESS2

Electric Range Right Rear Surface Element Switch Replacement

Tools needed: Phillips-head screwdriver, flat-head screwdriver

Shock

Be sure to unplug the power cord or shut off the power supply.

Open the oven door and use a Phillips-head screwdriver to unthread the screws securing the control panel?s lower cover.

Sharp

Remove the cover.

Next, unthread the two screws securing the control panel to the frame.

Place a towel on the cooktop surface then detach the control panel and rest it on the towel.

Pull off the right rear surface element switch control knob.

Unthread the two screws securing the control knob bezel and the switch itself.

If applicable, remove the gasket.

You can use a flat-head screwdriver to help disconnect the two wire connecters to fully remove the old switch.

Install the new surface element switch by first connecting the wire connecters.

Slide the gasket over the switch stem, then position the switch in the control panel

Realign the bezel with the red marking on top, then thread and tighten the two screws to secure.

Slide the knob onto the new switch stem.

Realign the control panel on the front brackets.

Secure it with the screws.

Replace the lower cover, then thread the screws to secure.

Plug the power cord back in or restore the power supply and the electric range should be ready for use.

Applicable Product Model

Brand

KitchenAid

Product Type

Range/Stove/Oven

Model

KSEB900ESS2

Subtype

Electric

Product Diagram & Manuals

Parts Needed

Surface Element Switch

$93.57

Recommended Tools and Accessories

Cooktop Cleaner

$14.29

Total$0.00

Kitchenaid Electric Slide-In Range Right Rear Surface Element Switch Replacement #W10911303

Step By Step Instructions

Applicable Product Model

Related Articles & Videos