Kitchenaid Electric Slide-In Range Terminal Block Replacement #WPW10245259

Print ContentSave Content

Skill Level

Total Parts Cost

$29.47

Estimated Savings

$112.50

04:13

Description

This video provides step-by-step instructions for replacing the terminal block on a Kitchenaid electric slide-in range (model #KSEB900ESS2). The most common reason for replacing the block is if the oven is not receiving power.

All of the information in this terminal block replacement video is applicable to the following brands: Maytag, Amana, Magic Chef, Whirlpool, Tappan, Estate, Kitchenaide

Step By Step Instructions

Print Instructions

KitchenAid Electric Slide-In Range - KSEB900ESS2

Electric Range Terminal Block Replacement

Tools needed: Phillips-head screwdriver, 3/8th inch socket or nut driver

Shock

Be sure to unplug the power cord or shut off the power supply.

Pull the range away from the wall so you can access the rear of the appliance.

Using a Phillips-head screwdriver, unthread the two screws securing the lower rear access panel.

Sharp

Lift the panel up and out to remove.

Use a 3/8th inch socket or nut driver to unthread the nuts securing the power cord wires.

Note the orientation of the wires then pull them free.

Next, unthread the nuts to release the main supply wires.

Detach the filter board from the terminal block posts.

Use the Phillips-head screwdriver to unthread the appropriate screws to fully remove the old terminal block.

You?re now ready to install the new terminal block.

If your range uses a four-wire power cord, you should cut off the grounding strap.

Make sure the insulator is aligned behind the terminal block, then thread and tighten the screws to secure.

Reposition the filter board, align the main supply wires on the posts, then thread the nuts to secure.

Align the power cord wires and secure them with the nuts.

Reinstall the lower access panel by inserting the tabs in the slots first.

Lower the panel and secure it with the screws.

Plug the power cord back in or restore the power supply and the electric range should be ready for use.

Description

Step-By-Step Instructions

KitchenAid Electric Slide-In Range - KSEB900ESS2

Electric Range Terminal Block Replacement

Tools needed: Phillips-head screwdriver, 3/8th inch socket or nut driver

Shock

Be sure to unplug the power cord or shut off the power supply.

Pull the range away from the wall so you can access the rear of the appliance.

Using a Phillips-head screwdriver, unthread the two screws securing the lower rear access panel.

Sharp

Lift the panel up and out to remove.

Use a 3/8th inch socket or nut driver to unthread the nuts securing the power cord wires.

Note the orientation of the wires then pull them free.

Next, unthread the nuts to release the main supply wires.

Detach the filter board from the terminal block posts.

Use the Phillips-head screwdriver to unthread the appropriate screws to fully remove the old terminal block.

You?re now ready to install the new terminal block.

If your range uses a four-wire power cord, you should cut off the grounding strap.

Make sure the insulator is aligned behind the terminal block, then thread and tighten the screws to secure.

Reposition the filter board, align the main supply wires on the posts, then thread the nuts to secure.

Align the power cord wires and secure them with the nuts.

Reinstall the lower access panel by inserting the tabs in the slots first.

Lower the panel and secure it with the screws.

Plug the power cord back in or restore the power supply and the electric range should be ready for use.

Applicable Product Model

Brand

KitchenAid

Product Type

Range/Stove/Oven

Model

KSEB900ESS2

Subtype

Electric

Product Diagram & Manuals

Parts Needed

Terminal Block

$29.47

Recommended Tools and Accessories

$35.70

$45.68

$5.50

$14.19

Total$0.00

Kitchenaid Electric Slide-In Range Terminal Block Replacement #WPW10245259

Step By Step Instructions

Applicable Product Model

Related Articles & Videos