In-stock parts ship the same day
Price Match Guarantee
In-stock parts ship the same dayGET PRO PRICING
Video & Articles: Appliance & Equipment RepairKitchenaid Electric Slide-In Range Right Rear Radiant Surface Element Replacement #WP8273994
Kitchenaid Electric Slide-In Range Right Rear Radiant Surface Element Replacement #WP8273994
Skill Level
Total Parts Cost
$152.36Estimated Savings
$112.5004:59
- Description
This video provides step-by-step instructions for replacing the right rear radiant surface element on a Kitchenaid electric slide-in range (model #KSEB900ESS2). The most common reason for replacing the element is if it will not heat.
All of the information in this element replacement video is applicable to the following brands: Maytag, Amana, Magic Chef, Whirlpool, Tappan, Estate, Kitchenaide
All of the information in this element replacement video is applicable to the following brands: Maytag, Amana, Magic Chef, Whirlpool, Tappan, Estate, Kitchenaide
Step By Step Instructions
1
KitchenAid Electric Slide-In Range - KSEB900ESS2
2
Electric Range Right Rear Radiant Surface Element Replacement
3
Tools needed: Phillips-head screwdriver
4
Shock
5
Be sure to unplug the power cord or shut off the power supply.
6
Open the oven door and use a Phillips-head screwdriver to unthread the screws securing the control panel?s lower cover.
7
Sharp
8
Remove the cover.
9
Next, unthread the two screws securing the control panel to the frame.
10
Detach the control panel and support it to avoid straining the wires.
11
Now unthread the front bracket screws securing the main top.
12
Unthread the two screws underneath the rear corners of the top.
13
Sharp
14
Pull the main top back and up to remove then set it aside.
15
Detach the right rear radiant surface element retaining clips from the support panel.
16
Note the orientation of the wires then disconnect them from the terminals.
17
Prepare the new radiant surface element for installation by transferring the spring clips from the old element to the new one.
18
Use the numbers engraved on the base to position the clips in the proper locations.
19
Connect the wires to the appropriate terminals.
20
Insert the clips into the slots in the support panel and snap the new element into place.
21
Reposition the main top by sliding the rear edge under the lip of the element support panel, then lower the front edge.
22
Replace all of the screws to secure.
23
Realign the control panel on the front brackets.
24
Secure it with the screws.
25
Replace the lower cover, then thread the screws to secure.
26
Plug the power cord back in or restore the power supply and the electric range should be ready for use.
Description
This video provides step-by-step instructions for replacing the right rear radiant surface element on a Kitchenaid electric slide-in range (model #KSEB900ESS2). The most common reason for replacing the element is if it will not heat.
All of the information in this element replacement video is applicable to the following brands: Maytag, Amana, Magic Chef, Whirlpool, Tappan, Estate, Kitchenaide
All of the information in this element replacement video is applicable to the following brands: Maytag, Amana, Magic Chef, Whirlpool, Tappan, Estate, Kitchenaide
Step-By-Step Instructions
1
KitchenAid Electric Slide-In Range - KSEB900ESS2
2
Electric Range Right Rear Radiant Surface Element Replacement
3
Tools needed: Phillips-head screwdriver
4
Shock
5
Be sure to unplug the power cord or shut off the power supply.
6
Open the oven door and use a Phillips-head screwdriver to unthread the screws securing the control panel?s lower cover.
7
Sharp
8
Remove the cover.
9
Next, unthread the two screws securing the control panel to the frame.
10
Detach the control panel and support it to avoid straining the wires.
11
Now unthread the front bracket screws securing the main top.
12
Unthread the two screws underneath the rear corners of the top.
13
Sharp
14
Pull the main top back and up to remove then set it aside.
15
Detach the right rear radiant surface element retaining clips from the support panel.
16
Note the orientation of the wires then disconnect them from the terminals.
17
Prepare the new radiant surface element for installation by transferring the spring clips from the old element to the new one.
18
Use the numbers engraved on the base to position the clips in the proper locations.
19
Connect the wires to the appropriate terminals.
20
Insert the clips into the slots in the support panel and snap the new element into place.
21
Reposition the main top by sliding the rear edge under the lip of the element support panel, then lower the front edge.
22
Replace all of the screws to secure.
23
Realign the control panel on the front brackets.
24
Secure it with the screws.
25
Replace the lower cover, then thread the screws to secure.
26
Plug the power cord back in or restore the power supply and the electric range should be ready for use.
Applicable Product Model
Parts Needed
Radiant Surface Element
$152.36
Recommended Tools and Accessories
Cooktop Cleaner
$14.19
Total$0.00
Related Articles & Videos
02:28
Part Replacement
Kitchenaid Double Oven Electric Range Right Rear Surface Element Replacement #WP8273994
06:57
Part Replacement
Kitchenaid Electric Downdraft Cooktop Element (1200W) Replacement #WP8273994