In-stock parts ship the same day
Price Match Guarantee
In-stock parts ship the same dayGET PRO PRICING
Video & Articles: Appliance & Equipment RepairGE Washer Pressure Hose Replacement WH41X24395
This video provides step-by-step repair instructions for replacing the pressure hose in a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
GE Washer Pressure Hose Replacement WH41X24395
Total Parts Cost
$NaN08:11
- Description
This video provides step-by-step repair instructions for replacing the pressure hose in a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
To replace the pressure sensor hose in your ge washer, you will need a drill driver with a 1/4” bit, a utility knife, a putty knife, and pliers.
2
Before you begin the procedure, unplug the power to the washer.
3
Shut off the water supply
4
Remove the drain line from the wall
5
Remove the hot and cold-water supply lines from the inlet valves, be prepared for water to spill out.
6
Unthread the two screws on the panel. any missing screws can be ordered through the links in the description below.
7
Pull the panel out from the bottom and slide it to the right to free it from the backsplash.
8
Slide the backsplash back and tilt forward
9
Note the orientation of the wires and use the needlenose pliers to remove them from the capacitor.
10
You can release electricity in the capacitor by placing a screwdriver over the two terminals. be careful not to let your hands come in contact with the shaft of the screwdriver.
11
Carefully slide the capacitor to the left
12
Noting the orientation, unplug all the harnesses on the circuit board except for the switch harness.
13
Remove the hose.
14
Depress the tab on the data port and push down to remove it.
15
Unthread the ground screw to the main harness.
16
Now remove the two ¼” screws.
17
Insert the putty knife approximatly 8 ½ “
18
From the edge on both sides and press in firmly to release the spring clips from the panel.
19
Lift off the top panel and remove the wire harness retainer.
20
Pushing the tub aside, reach towards the bottom and remove the pressure hose.
21
Using the utility knife, carefully cut the tape securing the hose to the harness.
22
Pull the hose from the wire harness retainer.
23
To install the new pressure sensor hose, feed the hose through the wire retainer. you can use dishsoap to help lubricate it for easier install.
24
Wrap the hose around the main harness.
25
Fit the hose over the nozzle on the tub.
26
Set the top back on the washer and attach the harness retainer.
27
Firmly press down on the front of the top panel to secure it in place.
28
Rethread the two ¼” screws.
29
Rethread the ground screw to secure the ground wire to the top of the panel.
30
Place the backsplash back on the appliance.
31
Push the hose over the sensor.
32
Now plug in all the harnesses into their designated spots on the control board.
33
Insert the data port.
34
Plug the wires back into the capacitor
35
Slide the capacitor back into its groove
36
Tilt the backsplash upright and insert the tabs into the slots.
37
Insert the panel tabs into the slots on the backsplash then slide it left to secure it.
38
Rethread the two screws.
39
Reattach the hot and cold-water supply lines.
40
Insert the drain hose back into the wall drain.
41
Turn on the water supply
42
Plug in the power, and your washer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the pressure hose in a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
This video provides step-by-step repair instructions for replacing the pressure hose in a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
To replace the pressure sensor hose in your ge washer, you will need a drill driver with a 1/4” bit, a utility knife, a putty knife, and pliers.
2
Before you begin the procedure, unplug the power to the washer.
3
Shut off the water supply
4
Remove the drain line from the wall
5
Remove the hot and cold-water supply lines from the inlet valves, be prepared for water to spill out.
6
Unthread the two screws on the panel. any missing screws can be ordered through the links in the description below.
7
Pull the panel out from the bottom and slide it to the right to free it from the backsplash.
8
Slide the backsplash back and tilt forward
9
Note the orientation of the wires and use the needlenose pliers to remove them from the capacitor.
10
You can release electricity in the capacitor by placing a screwdriver over the two terminals. be careful not to let your hands come in contact with the shaft of the screwdriver.
11
Carefully slide the capacitor to the left
12
Noting the orientation, unplug all the harnesses on the circuit board except for the switch harness.
13
Remove the hose.
14
Depress the tab on the data port and push down to remove it.
15
Unthread the ground screw to the main harness.
16
Now remove the two ¼” screws.
17
Insert the putty knife approximatly 8 ½ “
18
From the edge on both sides and press in firmly to release the spring clips from the panel.
19
Lift off the top panel and remove the wire harness retainer.
20
Pushing the tub aside, reach towards the bottom and remove the pressure hose.
21
Using the utility knife, carefully cut the tape securing the hose to the harness.
22
Pull the hose from the wire harness retainer.
23
To install the new pressure sensor hose, feed the hose through the wire retainer. you can use dishsoap to help lubricate it for easier install.
24
Wrap the hose around the main harness.
25
Fit the hose over the nozzle on the tub.
26
Set the top back on the washer and attach the harness retainer.
27
Firmly press down on the front of the top panel to secure it in place.
28
Rethread the two ¼” screws.
29
Rethread the ground screw to secure the ground wire to the top of the panel.
30
Place the backsplash back on the appliance.
31
Push the hose over the sensor.
32
Now plug in all the harnesses into their designated spots on the control board.
33
Insert the data port.
34
Plug the wires back into the capacitor
35
Slide the capacitor back into its groove
36
Tilt the backsplash upright and insert the tabs into the slots.
37
Insert the panel tabs into the slots on the backsplash then slide it left to secure it.
38
Rethread the two screws.
39
Reattach the hot and cold-water supply lines.
40
Insert the drain hose back into the wall drain.
41
Turn on the water supply
42
Plug in the power, and your washer should be ready for use.
Applicable Product Model
Related Articles & Videos