In-stock parts ship the same day
Price Match Guarantee
In-stock parts ship the same dayGET PRO PRICING
Video & Articles: Appliance & Equipment RepairGE Washer Hub Washer Replacement WH02X10364
This video provides step-by-step repair instructions for replacing the hub washer in a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
GE Washer Hub Washer Replacement WH02X10364
Total Parts Cost
$NaN10:32
- Description
This video provides step-by-step repair instructions for replacing the hub washer in a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
To replace the hub washer in your ge washer, you will need a drill driver with a 1/4” bit, pliers, a putty knife, an impact driver with socket adapter or ratchet with extension, 3/8” to 1/2” socket adapter, an 11mm socket, 33mm deep well socket, a 1/4" to 3/8” socket adapter, a phillips screwdriver, and needlenose pliers.
2
Before you begin the procedure, unplug the power to the washer.
3
Shut off the water supply
4
Remove the drain line from the wall
5
Remove the hot and cold-water supply lines from the inlet valves, be prepared for water to spill out.
6
Remove the fabric softener dispenser.
7
Align the raised bump with the opening on the auger
8
Use the screwdriver to puncture through the inner shaft of the auger, then twist clockwise until the auger releases and lift it out. this will be difficult. be sure to hold the basket from rotating.
9
Unthread the 11mm bolt.
10
Lift out the base.
11
Unthread the 33mm nut. this will be difficult.
12
Pull out the belleville washer.
13
Unthread the two screws on the panel. any missing screws can be ordered through the links in the description below.
14
Pull the panel out from the bottom and slide it to the right to free it from the backsplash.
15
Slide the backsplash back and tilt forward
16
Pull up the capacitor to release it from the bracket.
17
Noting the orientation, unplug all the harnesses on the circuit board except for the switch harness.
18
Remove the hose.
19
Depress the tab on the data port and push down to remove it.
20
Unthread the ground screw to the main harness.
21
Now remove the two ¼” screws.
22
Insert the putty knife approximatly 8 ½”
23
From the edge on both sides and press in firmly to release the spring clips from the panel.
24
Lift off the top panel and remove the wire harness retainer.
25
Noting the orientation, unhook the eight tabs around the tub cover and lift it out.
26
Now lift out the basket.
27
If applicable, remove the hub washer.
28
To install the new hub washer, set the washer over the transmission shaft.
29
Place the basket into the tub and align it with the spline gear.
30
Place the belleville washer on the transmission shaft with the green dot facing upward.
31
Rethread the 33mm nut going counter-clockwise.
32
Align the tub cover with the lip of the tub and snap the eight tabs into place.
33
Set the top back on the washer and attach the harness retainer.
34
Firmly press down on the front of the top panel to secure it in place.
35
Rethread the two ¼” screws.
36
Rethread the ground screw to secure the ground wire to the top of the panel.
37
Place the backsplash back on the appliance.
38
Push the hose over the sensor.
39
Now plug in all the harnesses into their designated spots on the control board.
40
Insert the data port.
41
Align the capacitor with its groove and push down to secure it.
42
Tilt the backsplash upright and insert the tabs into the slots.
43
Insert the panel tabs into the slots on the backsplash then slide it left to secure it.
44
Rethread the two screws.
45
Align the base with the spline shaft and set it into the appliance.
46
Rethread the 11mm bolt to secure, set the auger over the tabs and twist counter-clockwise to lock it in place.
47
Align the dispenser to the grooves of the auger and press firmly to secure in place.
48
Reattach the hot and cold-water supply lines.
49
Insert the drain hose back into the wall drain.
50
Turn on the water supply
51
Plug in the power, and your washer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the hub washer in a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
This video provides step-by-step repair instructions for replacing the hub washer in a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
To replace the hub washer in your ge washer, you will need a drill driver with a 1/4” bit, pliers, a putty knife, an impact driver with socket adapter or ratchet with extension, 3/8” to 1/2” socket adapter, an 11mm socket, 33mm deep well socket, a 1/4" to 3/8” socket adapter, a phillips screwdriver, and needlenose pliers.
2
Before you begin the procedure, unplug the power to the washer.
3
Shut off the water supply
4
Remove the drain line from the wall
5
Remove the hot and cold-water supply lines from the inlet valves, be prepared for water to spill out.
6
Remove the fabric softener dispenser.
7
Align the raised bump with the opening on the auger
8
Use the screwdriver to puncture through the inner shaft of the auger, then twist clockwise until the auger releases and lift it out. this will be difficult. be sure to hold the basket from rotating.
9
Unthread the 11mm bolt.
10
Lift out the base.
11
Unthread the 33mm nut. this will be difficult.
12
Pull out the belleville washer.
13
Unthread the two screws on the panel. any missing screws can be ordered through the links in the description below.
14
Pull the panel out from the bottom and slide it to the right to free it from the backsplash.
15
Slide the backsplash back and tilt forward
16
Pull up the capacitor to release it from the bracket.
17
Noting the orientation, unplug all the harnesses on the circuit board except for the switch harness.
18
Remove the hose.
19
Depress the tab on the data port and push down to remove it.
20
Unthread the ground screw to the main harness.
21
Now remove the two ¼” screws.
22
Insert the putty knife approximatly 8 ½”
23
From the edge on both sides and press in firmly to release the spring clips from the panel.
24
Lift off the top panel and remove the wire harness retainer.
25
Noting the orientation, unhook the eight tabs around the tub cover and lift it out.
26
Now lift out the basket.
27
If applicable, remove the hub washer.
28
To install the new hub washer, set the washer over the transmission shaft.
29
Place the basket into the tub and align it with the spline gear.
30
Place the belleville washer on the transmission shaft with the green dot facing upward.
31
Rethread the 33mm nut going counter-clockwise.
32
Align the tub cover with the lip of the tub and snap the eight tabs into place.
33
Set the top back on the washer and attach the harness retainer.
34
Firmly press down on the front of the top panel to secure it in place.
35
Rethread the two ¼” screws.
36
Rethread the ground screw to secure the ground wire to the top of the panel.
37
Place the backsplash back on the appliance.
38
Push the hose over the sensor.
39
Now plug in all the harnesses into their designated spots on the control board.
40
Insert the data port.
41
Align the capacitor with its groove and push down to secure it.
42
Tilt the backsplash upright and insert the tabs into the slots.
43
Insert the panel tabs into the slots on the backsplash then slide it left to secure it.
44
Rethread the two screws.
45
Align the base with the spline shaft and set it into the appliance.
46
Rethread the 11mm bolt to secure, set the auger over the tabs and twist counter-clockwise to lock it in place.
47
Align the dispenser to the grooves of the auger and press firmly to secure in place.
48
Reattach the hot and cold-water supply lines.
49
Insert the drain hose back into the wall drain.
50
Turn on the water supply
51
Plug in the power, and your washer should be ready for use.
Applicable Product Model
Related Articles & Videos