In-stock parts ship the same day
Price Match Guarantee
In-stock parts ship the same dayGET PRO PRICING
Video & Articles: Appliance & Equipment RepairGE Washer Button Tree Replacement WH01X24376
This video provides step-by-step repair instructions for replacing the button tree on a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
GE Washer Button Tree Replacement WH01X24376
Total Parts Cost
$NaN03:53
- Description
This video provides step-by-step repair instructions for replacing the button tree on a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
To replace the button tree on your ge washer, you will need a drill driver with a 1/4” bit and needlenose pliers.
2
Before you begin the procedure, unplug the power to the appliance.
3
Pull the wash selector knob to remove it.
4
Unthread the two screws on the panel. any missing screws can be ordered through the links in the description below.
5
Pull the panel out from the bottom and slide it to the right to free it from the backsplash.
6
Slide the backsplash back and tilt forward.
7
Unthread the four screws holding the bracket.
8
Unhook the harness from the bracket.
9
Squeeze the two pegs to fully release the bracket.
10
Gently lift the control board to reveal the button tree and remove it.
11
To install the new button tree, postion it in the backsplash.
12
Gently set the control board inside the backsplash and align it with the four mounting holes.
13
Snap the two pegs of the bracket into the control board.
14
Loop the harness around the hook.
15
Rethread the four screws.
16
Tilt the backsplash upright and insert the tabs into the slots.
17
Push forward to lock it in place.
18
Insert the panel tabs into the slots on the backsplash then slide it left to secure it.
19
Rethread the two screws.
20
Align the knob on the d-shaft and press into place, plug in the washer.
Description
This video provides step-by-step repair instructions for replacing the button tree on a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
This video provides step-by-step repair instructions for replacing the button tree on a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
To replace the button tree on your ge washer, you will need a drill driver with a 1/4” bit and needlenose pliers.
2
Before you begin the procedure, unplug the power to the appliance.
3
Pull the wash selector knob to remove it.
4
Unthread the two screws on the panel. any missing screws can be ordered through the links in the description below.
5
Pull the panel out from the bottom and slide it to the right to free it from the backsplash.
6
Slide the backsplash back and tilt forward.
7
Unthread the four screws holding the bracket.
8
Unhook the harness from the bracket.
9
Squeeze the two pegs to fully release the bracket.
10
Gently lift the control board to reveal the button tree and remove it.
11
To install the new button tree, postion it in the backsplash.
12
Gently set the control board inside the backsplash and align it with the four mounting holes.
13
Snap the two pegs of the bracket into the control board.
14
Loop the harness around the hook.
15
Rethread the four screws.
16
Tilt the backsplash upright and insert the tabs into the slots.
17
Push forward to lock it in place.
18
Insert the panel tabs into the slots on the backsplash then slide it left to secure it.
19
Rethread the two screws.
20
Align the knob on the d-shaft and press into place, plug in the washer.
Applicable Product Model
Related Articles & Videos