In-stock parts ship the same day
Price Match Guarantee
In-stock parts ship the same dayGET PRO PRICING
Video & Articles: Appliance & Equipment RepairGE Washer Selector Switch Harness Replacement WH04X29308
This video provides step-by-step repair instructions for replacing the selector switch harness on a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
GE Washer Selector Switch Harness Replacement WH04X29308
Total Parts Cost
$NaN03:48
- Description
This video provides step-by-step repair instructions for replacing the selector switch harness on a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
To replace the selector switch harness in your ge washer, you will need a drill driver with a 1/4” bit and needlenose pliers.
2
Before you begin the procedure, unplug the power to the appliance.
3
Remove the four option selector knobs.
4
Unthread the two screws on the panel. any missing screws can be ordered through the links in the description below.
5
Pull the panel out from the bottom and slide it to the right to free it from the backsplash.
6
Slide the backsplash back and tilt forward.
7
Unplug the selector harness.
8
Unhook the harness from the bracket.
9
Note the orientation of each switch.
10
pull the tab back and twist counterclockwise to remove the switches.
11
To install the new selector switch harness, feed the harness through the panel.
12
Insert each switch and twist clockwise to lock in place
13
Hook the harness into the bracket.
14
Plug the harness into the control board.
15
Tilt the backsplash upright and insert the tabs into the slots.
16
Push forward to lock it in place.
17
Insert the panel tabs into the slots on the backsplash then slide it left to secure it.
18
Rethread the two screws.
19
Align the selector option knobs on the d-shafts and press into place, plug in the washer, and your washer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the selector switch harness on a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
This video provides step-by-step repair instructions for replacing the selector switch harness on a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
To replace the selector switch harness in your ge washer, you will need a drill driver with a 1/4” bit and needlenose pliers.
2
Before you begin the procedure, unplug the power to the appliance.
3
Remove the four option selector knobs.
4
Unthread the two screws on the panel. any missing screws can be ordered through the links in the description below.
5
Pull the panel out from the bottom and slide it to the right to free it from the backsplash.
6
Slide the backsplash back and tilt forward.
7
Unplug the selector harness.
8
Unhook the harness from the bracket.
9
Note the orientation of each switch.
10
pull the tab back and twist counterclockwise to remove the switches.
11
To install the new selector switch harness, feed the harness through the panel.
12
Insert each switch and twist clockwise to lock in place
13
Hook the harness into the bracket.
14
Plug the harness into the control board.
15
Tilt the backsplash upright and insert the tabs into the slots.
16
Push forward to lock it in place.
17
Insert the panel tabs into the slots on the backsplash then slide it left to secure it.
18
Rethread the two screws.
19
Align the selector option knobs on the d-shafts and press into place, plug in the washer, and your washer should be ready for use.
Applicable Product Model
Related Articles & Videos