In-stock parts ship the same day
Price Match Guarantee
In-stock parts ship the same dayGET PRO PRICING
Video & Articles: Appliance & Equipment RepairGE Washer Backsplash Replacement WH22X28844
This video provides step-by-step repair instructions for replacing the backsplash on a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
GE Washer Backsplash Replacement WH22X28844
Total Parts Cost
$NaN06:33
- Description
This video provides step-by-step repair instructions for replacing the backsplash on a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
To replace the backsplash on your ge washer, you will need a drill driver with a 1/4” bit and needlenose pliers.
2
Before you begin the procedure, unplug the power to the appliance.
3
Pull and remove all the wash selector knobs.
4
Unthread the two screws on the panel. any missing screws can be ordered through the links in the description below.
5
Pull the panel out from the bottom and slide it to the right to free it from the backsplash.
6
Slide the backsplash back and tilt forward.
7
Unplug the selector harness.
8
Unhook the harness from the bracket.
9
Note the orientation of each switch.
10
Pull the tab back and twist counterclockwise to remove the switches.
11
Noting the orientation unplug all the harnesses.
12
Remove the hose.
13
Unthread the four screws holding the bracket.
14
Squeeze the two pegs to fully release the bracket.
15
Remove the control board.
16
Lift out the button tree.
17
Depress the tab in on the data port and push down to remove it.
18
To install the new backsplash…
19
Insert the data port.
20
Insert the button tree.
21
Gently set the control board in the backsplash and align it with the four mounting holes.
22
Mount the bracket by snapping the two pegs into the control board.
23
Rethread the four screws.
24
Push the hose over the sensor
25
Plug in all of the wire harnesses
26
Insert each switch and twist clockwise to lock in place
27
Loop the harness around the hook.
28
Plug the harness into the control board.
29
Tilt the backsplash upright and insert the tabs into the slots.
30
Push forward to lock it in place.
31
Insert the panel tabs into the slots on the backsplash then slide it left to secure it.
32
Rethread the two screws.
33
Align the knobs on the d-shafts and press into place.
34
Plug in the washer.
Description
This video provides step-by-step repair instructions for replacing the backsplash on a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
This video provides step-by-step repair instructions for replacing the backsplash on a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
To replace the backsplash on your ge washer, you will need a drill driver with a 1/4” bit and needlenose pliers.
2
Before you begin the procedure, unplug the power to the appliance.
3
Pull and remove all the wash selector knobs.
4
Unthread the two screws on the panel. any missing screws can be ordered through the links in the description below.
5
Pull the panel out from the bottom and slide it to the right to free it from the backsplash.
6
Slide the backsplash back and tilt forward.
7
Unplug the selector harness.
8
Unhook the harness from the bracket.
9
Note the orientation of each switch.
10
Pull the tab back and twist counterclockwise to remove the switches.
11
Noting the orientation unplug all the harnesses.
12
Remove the hose.
13
Unthread the four screws holding the bracket.
14
Squeeze the two pegs to fully release the bracket.
15
Remove the control board.
16
Lift out the button tree.
17
Depress the tab in on the data port and push down to remove it.
18
To install the new backsplash…
19
Insert the data port.
20
Insert the button tree.
21
Gently set the control board in the backsplash and align it with the four mounting holes.
22
Mount the bracket by snapping the two pegs into the control board.
23
Rethread the four screws.
24
Push the hose over the sensor
25
Plug in all of the wire harnesses
26
Insert each switch and twist clockwise to lock in place
27
Loop the harness around the hook.
28
Plug the harness into the control board.
29
Tilt the backsplash upright and insert the tabs into the slots.
30
Push forward to lock it in place.
31
Insert the panel tabs into the slots on the backsplash then slide it left to secure it.
32
Rethread the two screws.
33
Align the knobs on the d-shafts and press into place.
34
Plug in the washer.
Applicable Product Model
Related Articles & Videos