In-stock parts ship the same day
Price Match Guarantee
In-stock parts ship the same dayGET PRO PRICING
Video & Articles: Appliance & Equipment RepairGE Washer Top Panel Replacement WH44X24383
This video provides step-by-step repair instructions for replacing the top panel on a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
GE Washer Top Panel Replacement WH44X24383
Total Parts Cost
$NaN10:19
- Description
This video provides step-by-step repair instructions for replacing the top panel on a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
To replace the top panel on your ge washer, you will need a drill driver with a 1/4” bit, a putty knife, pliers, a utility knife blade, a #2 phillips bit, and needlenose pliers.
2
Before you begin the procedure, unplug the power to the appliance.
3
Turn off the water supply.
4
Remove the hot and cold water supply lines from the inlet valve, be prepared for water to spill out.
5
Unthread the two screws on the panel. any missing screws can be ordered through the links in the description below.
6
Pull the panel out from the bottom and slide it to the right to free it from the backsplash.
7
Slide the backsplash back and tilt forward
8
Pull up the capacitor to release it from the bracket.
9
Pull up on the small tab of the bracket and twist it 45°, then lift to remove it.
10
Noting the orientation, unplug all the harnesses on the circuit board except for the switch harness.
11
Remove the hose.
12
Depress the tab on the data port and push down to remove it.
13
Remove the two screws from the inlet valve bracket and lift it off of the assembly.
14
Push the assembly forward then lift up and slide it out from the appliance.
15
Remove the two ground screws.
16
Pull upward on the front of the cord while pushing forward to release it from the appliance.
17
Unthread the two hinge bushing screws.
18
Lift the tabs to a 90° angle and lift the lid off, move the tub forward to make it easier to reach the bezel.
19
As soon as you feel the tabs to the bezel, push them outward then push up to free it. then repeat the same action for the other side.
20
Press in and up on the bleach cup to remove it.
21
Now remove the two ¼” screws.
22
Insert the putty knife approximatly 8 ½ “
23
From the edge on both sides and press in firmly to release the spring clips from the panel.
24
Lift off the top panel and remove the wire harness retainer.
25
Move the top to a flat surface.
26
Use the utility blade to remove the two steel wire retaining clips.
27
Pull the retaining clips out of the top then flip the panel.
28
Pinch the harness retaining clip and push it down to remove.
29
Use the putty knife to depress the tab and slide the lid lock free from the top.
30
To install the new top panel, slide and snap the lock into postion.
31
Flip the panel over and run the plug end of the harness through the top and snap it in place.
32
Insert the two harness retaining clips.
33
Tuck the harness into the inner lip while snapping the steel retaining clips along the edge of the top.
34
Set the top back on the washer and attach the harness retainer.
35
Firmly press down on the front of the top panel to secure it in place.
36
Rethread the two ¼” screws.
37
Place the ear of the bleach cup into the slot and snap into position.
38
Place the ears of the bezel into the slots and snap into position.
39
While holding the bushings at 90°, set the front lid on the washer then lower the bushings into the holes.
40
Once seated push the tabs down and rethread the screws to secure the lid.
41
Place the cord tabs in the slot and pull back to secure it in place.
42
Rethread the two ground screws to secure the ground wires to the top.
43
Insert the inlet valve into the appliance and slide forward into position.
44
Align the mounting holes and place the bracket over the two pegs.
45
Push the hose over the sensor.
46
Now plug in all the harnesses into their designated spots on the control board.
47
Insert the data port.
48
Insert the capacitor bracket at a 45° angle and twist to lock it in place.
49
Align the capacitor with its groove and push down to secure it.
50
Tilt the backsplash upright and insert the tabs into the slots.
51
Insert the panel tabs into the slots on the backsplash then slide it left to secure it.
52
Attach the hot and cold water supply lines.
53
Turn the water supply back on.
54
Plug in the washer.
55
And your washer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the top panel on a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
This video provides step-by-step repair instructions for replacing the top panel on a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
To replace the top panel on your ge washer, you will need a drill driver with a 1/4” bit, a putty knife, pliers, a utility knife blade, a #2 phillips bit, and needlenose pliers.
2
Before you begin the procedure, unplug the power to the appliance.
3
Turn off the water supply.
4
Remove the hot and cold water supply lines from the inlet valve, be prepared for water to spill out.
5
Unthread the two screws on the panel. any missing screws can be ordered through the links in the description below.
6
Pull the panel out from the bottom and slide it to the right to free it from the backsplash.
7
Slide the backsplash back and tilt forward
8
Pull up the capacitor to release it from the bracket.
9
Pull up on the small tab of the bracket and twist it 45°, then lift to remove it.
10
Noting the orientation, unplug all the harnesses on the circuit board except for the switch harness.
11
Remove the hose.
12
Depress the tab on the data port and push down to remove it.
13
Remove the two screws from the inlet valve bracket and lift it off of the assembly.
14
Push the assembly forward then lift up and slide it out from the appliance.
15
Remove the two ground screws.
16
Pull upward on the front of the cord while pushing forward to release it from the appliance.
17
Unthread the two hinge bushing screws.
18
Lift the tabs to a 90° angle and lift the lid off, move the tub forward to make it easier to reach the bezel.
19
As soon as you feel the tabs to the bezel, push them outward then push up to free it. then repeat the same action for the other side.
20
Press in and up on the bleach cup to remove it.
21
Now remove the two ¼” screws.
22
Insert the putty knife approximatly 8 ½ “
23
From the edge on both sides and press in firmly to release the spring clips from the panel.
24
Lift off the top panel and remove the wire harness retainer.
25
Move the top to a flat surface.
26
Use the utility blade to remove the two steel wire retaining clips.
27
Pull the retaining clips out of the top then flip the panel.
28
Pinch the harness retaining clip and push it down to remove.
29
Use the putty knife to depress the tab and slide the lid lock free from the top.
30
To install the new top panel, slide and snap the lock into postion.
31
Flip the panel over and run the plug end of the harness through the top and snap it in place.
32
Insert the two harness retaining clips.
33
Tuck the harness into the inner lip while snapping the steel retaining clips along the edge of the top.
34
Set the top back on the washer and attach the harness retainer.
35
Firmly press down on the front of the top panel to secure it in place.
36
Rethread the two ¼” screws.
37
Place the ear of the bleach cup into the slot and snap into position.
38
Place the ears of the bezel into the slots and snap into position.
39
While holding the bushings at 90°, set the front lid on the washer then lower the bushings into the holes.
40
Once seated push the tabs down and rethread the screws to secure the lid.
41
Place the cord tabs in the slot and pull back to secure it in place.
42
Rethread the two ground screws to secure the ground wires to the top.
43
Insert the inlet valve into the appliance and slide forward into position.
44
Align the mounting holes and place the bracket over the two pegs.
45
Push the hose over the sensor.
46
Now plug in all the harnesses into their designated spots on the control board.
47
Insert the data port.
48
Insert the capacitor bracket at a 45° angle and twist to lock it in place.
49
Align the capacitor with its groove and push down to secure it.
50
Tilt the backsplash upright and insert the tabs into the slots.
51
Insert the panel tabs into the slots on the backsplash then slide it left to secure it.
52
Attach the hot and cold water supply lines.
53
Turn the water supply back on.
54
Plug in the washer.
55
And your washer should be ready for use.
Applicable Product Model
Related Articles & Videos