Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool Top-Load Washer User Interface Panel Wire Harness Replacement W11130939 
Whirlpool Top-Load Washer User Interface Panel Wire Harness Replacement W11130939
Skill Level
Total Parts Cost
$13.98Estimated Savings
$112.5004:30
- Description
This video provides step-by-step instructions for replacing the user interface panel wire harness on a Whirlpool top-loading washing machine, model WTW7120HW0. The most common reason for replacing this part is if the panel will not power on.
All of the information in this part replacement video is applicable to the following brands: Whirlpool
All of the information in this part replacement video is applicable to the following brands: Whirlpool
Step By Step Instructions
1
To replace the user interface panel wire harness in this Whirlpool top load washer, you will need a quarter inch nut driver and a putty knife.
2
Before you begin the procedure, unplug the appliance's power cord.
3
Have an assistant help you to move the washer away from the wall.
4
Use the quarter inch nut driver to unthread the two rear screws securing the control panel assembly.
5
Next, insert a putty knife under the front corners of the control panel housing to release the clips securing the housing.
6
Disconnect the user interface control wire connector so you can set the control panel assembly aside.
7
Next, unthread the eight screws securing the user interface panel to the housing using the quarter-inch nut driver.
8
With the screws unthreaded, release the wires from the retainer, then depress the retaining tabs to fully release the user interface panel from the housing.
9
You can now release the old wire harness from the retainers, then disconnect it from the user interface board to fully remove.
10
To install the new user interface panel wire harness, connect the appropriate end to the board, then secure the wires under the retainers.
11
Insert the opposite wire connector through the hole in the control panel housing as you position the user interface panel, then snap the panel into place.
12
Thread the eight screws to secure.
13
Secure the wires in the retainer.
14
Connect the user interface control wire connector to the main control board.
15
Insert the rear control panel housing clips in the rear slots in the main top first, then snap the front clips into place.
16
Re-thread the two rear screws to fully secure.
17
Move the washer back against the wall.
18
Plug the appliance's power cord back in, and the washer should be ready for use.
Description
This video provides step-by-step instructions for replacing the user interface panel wire harness on a Whirlpool top-loading washing machine, model WTW7120HW0. The most common reason for replacing this part is if the panel will not power on.
All of the information in this part replacement video is applicable to the following brands: Whirlpool
All of the information in this part replacement video is applicable to the following brands: Whirlpool
Step-By-Step Instructions
1
To replace the user interface panel wire harness in this Whirlpool top load washer, you will need a quarter inch nut driver and a putty knife.
2
Before you begin the procedure, unplug the appliance's power cord.
3
Have an assistant help you to move the washer away from the wall.
4
Use the quarter inch nut driver to unthread the two rear screws securing the control panel assembly.
5
Next, insert a putty knife under the front corners of the control panel housing to release the clips securing the housing.
6
Disconnect the user interface control wire connector so you can set the control panel assembly aside.
7
Next, unthread the eight screws securing the user interface panel to the housing using the quarter-inch nut driver.
8
With the screws unthreaded, release the wires from the retainer, then depress the retaining tabs to fully release the user interface panel from the housing.
9
You can now release the old wire harness from the retainers, then disconnect it from the user interface board to fully remove.
10
To install the new user interface panel wire harness, connect the appropriate end to the board, then secure the wires under the retainers.
11
Insert the opposite wire connector through the hole in the control panel housing as you position the user interface panel, then snap the panel into place.
12
Thread the eight screws to secure.
13
Secure the wires in the retainer.
14
Connect the user interface control wire connector to the main control board.
15
Insert the rear control panel housing clips in the rear slots in the main top first, then snap the front clips into place.
16
Re-thread the two rear screws to fully secure.
17
Move the washer back against the wall.
18
Plug the appliance's power cord back in, and the washer should be ready for use.
Applicable Product Model
Related Articles & Videos
05:14
Part Replacement
Whirlpool Top-Load Washer Water Inlet Valve Replacement 218605101
05:41
Part Replacement
Whirlpool Top-Load Washer Lid Lock Assembly Replacement W11394572
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com