In-stock parts ship the same day
Price Match Guarantee
In-stock parts ship the same dayGET PRO PRICING
Video & Articles: Appliance & Equipment RepairToro Snowblower Insulator Replacement 121-0077
Toro Snowblower Insulator Replacement 121-0077
Total Parts Cost
$NaN06:13
- Description
This video provides step-by-step repair instructions for replacing the insulator on a Toro snowblower.
All of the information for this video is applicable to the following brands:
Toro
All of the information for this video is applicable to the following brands:
Toro
Step By Step Instructions
1
Toro Snowblower - Model 38752
2
Snowblower Carburetor Insulator Replacement
3
Tools Needed
4
You will need an 8mm socket, a 8mm wrench, a 3/8th inch socket, a half-inch socket and a 10mm socket for this procedure.
5
Hot
6
Make sure the engine has cooled.
7
Spill
8
Be sure to perform this procedure with little or no fuel in the tank.
9
Use an 8mm socket to unthread five of the six bolts securing the muffler cover.
10
Use a 8mm wrench to unthread the sixth bolt.
11
Use a 3/8th inch socket or nut driver to unthread the mounting bolt securing the housing to the rear bracket.
12
Unthread the screws to release the two retaining clamps holding the housing to the handle.
13
Use a half-inch socket to fully unthread the upper bolts securing the handle assembly.
14
Sharp
15
Lower the handle to fully remove the muffler cover.
16
Spill
17
Detach the primer hose from the carburetor ? be prepared for some fuel to spill.
18
Disconnect the wires from the key switch terminals.
19
Use a 10mm socket to unthread the nuts securing the control housing.
20
Pull the housing off of the mounting bolts.
21
Slide off the carburetor intake gasket.
22
Spill
23
Attach a pinch clamp to the fuel line, then release the fuel line from the carburetor.
24
Pull the carburetor forward enough to detach the throttle rod.
25
Detach the throttle spring and fully remove the carburetor.
26
Slide off the outlet gasket.
27
Lift the spark plug wire and the ignition wire off of the insulator and remove the old insulator.
28
Before installing the new carburetor insulator, confirm the insulator gasket is in place.
29
Slide on the new insulator and position the ignition wire and the spark plug wire in the notch.
30
Slide on the carburetor outlet gasket, followed by the carburetor itself.
31
Reattach the throttle spring and rod to the carburetor.
32
Attach the fuel line, then remove the pinch clamp.
33
Slide the intake gasket onto the mounting bolts.
34
Reposition the control housing, then thread and tighten the mounting nuts.
35
Connect the wires to the key switch terminals.
36
Reattach the primer hose to the carburetor.
37
Reposition the muffler cover and thread the six bolts to secure.
38
Reposition the handle assembly and rethread the upper bolts.
39
Align the two retaining clamps and thread the screws to secure the housing to the handle.
40
Rethread the mounting bolt to secure the housing to the rear bracket.
41
Refill the fuel tank if necessary.
42
Congrats! Your snowblower is ready for use.
Description
This video provides step-by-step repair instructions for replacing the insulator on a Toro snowblower.
All of the information for this video is applicable to the following brands:
Toro
All of the information for this video is applicable to the following brands:
Toro
Step-By-Step Instructions
1
Toro Snowblower - Model 38752
2
Snowblower Carburetor Insulator Replacement
3
Tools Needed
4
You will need an 8mm socket, a 8mm wrench, a 3/8th inch socket, a half-inch socket and a 10mm socket for this procedure.
5
Hot
6
Make sure the engine has cooled.
7
Spill
8
Be sure to perform this procedure with little or no fuel in the tank.
9
Use an 8mm socket to unthread five of the six bolts securing the muffler cover.
10
Use a 8mm wrench to unthread the sixth bolt.
11
Use a 3/8th inch socket or nut driver to unthread the mounting bolt securing the housing to the rear bracket.
12
Unthread the screws to release the two retaining clamps holding the housing to the handle.
13
Use a half-inch socket to fully unthread the upper bolts securing the handle assembly.
14
Sharp
15
Lower the handle to fully remove the muffler cover.
16
Spill
17
Detach the primer hose from the carburetor ? be prepared for some fuel to spill.
18
Disconnect the wires from the key switch terminals.
19
Use a 10mm socket to unthread the nuts securing the control housing.
20
Pull the housing off of the mounting bolts.
21
Slide off the carburetor intake gasket.
22
Spill
23
Attach a pinch clamp to the fuel line, then release the fuel line from the carburetor.
24
Pull the carburetor forward enough to detach the throttle rod.
25
Detach the throttle spring and fully remove the carburetor.
26
Slide off the outlet gasket.
27
Lift the spark plug wire and the ignition wire off of the insulator and remove the old insulator.
28
Before installing the new carburetor insulator, confirm the insulator gasket is in place.
29
Slide on the new insulator and position the ignition wire and the spark plug wire in the notch.
30
Slide on the carburetor outlet gasket, followed by the carburetor itself.
31
Reattach the throttle spring and rod to the carburetor.
32
Attach the fuel line, then remove the pinch clamp.
33
Slide the intake gasket onto the mounting bolts.
34
Reposition the control housing, then thread and tighten the mounting nuts.
35
Connect the wires to the key switch terminals.
36
Reattach the primer hose to the carburetor.
37
Reposition the muffler cover and thread the six bolts to secure.
38
Reposition the handle assembly and rethread the upper bolts.
39
Align the two retaining clamps and thread the screws to secure the housing to the handle.
40
Rethread the mounting bolt to secure the housing to the rear bracket.
41
Refill the fuel tank if necessary.
42
Congrats! Your snowblower is ready for use.
Applicable Product Model
Related Articles & Videos