In-stock parts ship the same day
Price Match Guarantee
In-stock parts ship the same dayGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool Washer Suspension Spring Retainer #W10145155
Whirlpool Washer Suspension Spring Retainer #W10145155
Skill Level
Total Parts Cost
$4.30Estimated Savings
$112.5002:53
- Description
This video provides step-by-step instructions for replacing the suspension spring retainer on top loading direct drive Whirlpool washing machines. The most common reason for replacing the suspension spring retainer is when the washer is shaking during the spin cycle.
All the information in this spring retainer replacement video is applicable to the following brands: Whirlpool, Kenmore, KitchenAid, Roper, Maytag, Estate, Inglis, Crosley, Amana, Admiral
Tools used: flat-head screwdriver, Phillips head screwdriver, pliers, putty knife, 7/16” socket
All the information in this spring retainer replacement video is applicable to the following brands: Whirlpool, Kenmore, KitchenAid, Roper, Maytag, Estate, Inglis, Crosley, Amana, Admiral
Tools used: flat-head screwdriver, Phillips head screwdriver, pliers, putty knife, 7/16” socket
Step By Step Instructions
1
As with any repair, be sure you've unplugged the appliance before beginning.
2
Your first step is to move the control panel out of the way.
3
To do this, remove the screws found at either end.
4
On some models, these screws may be located in the rear panel or they may be covered by plastic end caps.
5
Pull the end cap off from the top to access the screw.
6
Remove both screws and rotate the panel up.
7
Some models use clips instead of screws to secure the control panel.
8
Insert a putty knife between the control panel and the cabinet to release the clips.
9
Unplug the wire connector and snap out the spring clips.
10
Using a flathead screwdriver, tilt the cabinet towards you, slide forward, and remove.
11
Next, use pliers to remove the suspension spring from the mounting bracket.
12
Be aware, you may need to use force to successfully remove it.
13
Once the spring is off the bracket, detach it from the old suspension spring retainer.
14
Now, pull the old retainer out of its slot in the base.
15
Install the new retainer by inserting the short hook side into the base slot and snapping it into place.
16
Attach one end of the suspension spring to the retainer and the other end to the mounting bracket.
17
Now, reinstall the cabinet.
18
The front edge of the cabinet slides underneath the base frame.
19
Use your foot to push it into position.
20
Align the two notches in each side of the cabinet with the tabs on each side of the base frame.
21
Now, ease the cabinet to match up with the rear panel.
22
Reinstall the spring clips.
23
Reattach the wire connector.
24
Rotate the control panel down and lock the clips into place or reinstall the two screws if applicable to your model.
25
Replace the end caps by aligning the tab with the slot at the bottom and snapping the cap into position.
26
You're now ready to plug the appliance back in to make sure it's functioning properly.
Description
This video provides step-by-step instructions for replacing the suspension spring retainer on top loading direct drive Whirlpool washing machines. The most common reason for replacing the suspension spring retainer is when the washer is shaking during the spin cycle.
All the information in this spring retainer replacement video is applicable to the following brands: Whirlpool, Kenmore, KitchenAid, Roper, Maytag, Estate, Inglis, Crosley, Amana, Admiral
Tools used: flat-head screwdriver, Phillips head screwdriver, pliers, putty knife, 7/16” socket
All the information in this spring retainer replacement video is applicable to the following brands: Whirlpool, Kenmore, KitchenAid, Roper, Maytag, Estate, Inglis, Crosley, Amana, Admiral
Tools used: flat-head screwdriver, Phillips head screwdriver, pliers, putty knife, 7/16” socket
Step-By-Step Instructions
1
As with any repair, be sure you've unplugged the appliance before beginning.
2
Your first step is to move the control panel out of the way.
3
To do this, remove the screws found at either end.
4
On some models, these screws may be located in the rear panel or they may be covered by plastic end caps.
5
Pull the end cap off from the top to access the screw.
6
Remove both screws and rotate the panel up.
7
Some models use clips instead of screws to secure the control panel.
8
Insert a putty knife between the control panel and the cabinet to release the clips.
9
Unplug the wire connector and snap out the spring clips.
10
Using a flathead screwdriver, tilt the cabinet towards you, slide forward, and remove.
11
Next, use pliers to remove the suspension spring from the mounting bracket.
12
Be aware, you may need to use force to successfully remove it.
13
Once the spring is off the bracket, detach it from the old suspension spring retainer.
14
Now, pull the old retainer out of its slot in the base.
15
Install the new retainer by inserting the short hook side into the base slot and snapping it into place.
16
Attach one end of the suspension spring to the retainer and the other end to the mounting bracket.
17
Now, reinstall the cabinet.
18
The front edge of the cabinet slides underneath the base frame.
19
Use your foot to push it into position.
20
Align the two notches in each side of the cabinet with the tabs on each side of the base frame.
21
Now, ease the cabinet to match up with the rear panel.
22
Reinstall the spring clips.
23
Reattach the wire connector.
24
Rotate the control panel down and lock the clips into place or reinstall the two screws if applicable to your model.
25
Replace the end caps by aligning the tab with the slot at the bottom and snapping the cap into position.
26
You're now ready to plug the appliance back in to make sure it's functioning properly.
Applicable Product Model
Parts Needed
Spring Clip
$4.30
Total$0.00
Related Articles & Videos
04:10
Part Replacement
Washer Won't Spin? Replace Whirlpool Direct Drive Clutch Assembly Part # 285785